MAIN > DENTAL > REPAIR SERVICES > INTEGRAL PARTS

LABORATORY HANDPIECE           
H108 THUMBSCREW
H102 COLLET
H104 NOSE CONE
H106 NOSE CONE CONTRA ANGLE
H110 RUBBER WRENCH
H206 COLLET & THUMBSCREW
H208 NOSE CONE WITH RUBBER WRENCH
W011 WRIST JOINT
W204 SPRING CLIP KIT
W102 RETAINING SCREW (2 PK)


FOOT CONTROL PARTS           
F109 FUSE 5A/250V (2 PCS)
F113 PLUG RETAINER KIT
F200 CIRCUIT BOARD KIT
F202 CONNECTOR 6-PRONG MALE
F206 RETURN SPRING KIT
F208 SEMICONDUCTOR KIT
F506 MALE CONNECTOR
   
   
   


MOTORS, BRUSHES & REPAIR PARTS           
E132 MOTOR 115V
E133 MOTOR 230V
E101 BRUSHES FOR BALDOR E132 MOTOR (2 PCS)
E105 BRUSHES FOR BODINE E131 LARGE (2 PCS)
E106 BRUSHES FOR WSM MOTOR (2 PCS)
E107 BRUSHES FOR BODINE E129, E130 SMALL (2)
E150 MOTOR PULLEY WITH SCREW
E504 CONNECTOR 6-PRONG FEMALE
E112 POWER CORD KIT
E110 5-WIRE CORD KIT
   


SUPER QUICK CHUCK PARTS AND TOOLS
Q188 STOPS, SET OF 6
Q174 STOP LOCK SCREWS (PK OF 2)
Q559 TEST ROD 1/4"
Q240 SPECIAL COLLET COMPLETE
Q148 SPECIAL COLLET WITH SPRING
Q186 POP-OUT SPRING (PK OF 2)
Q149 SPECIAL COLLET
Q146 MASTER COLLET
Q542 SHIPPING ROD 3/32"
511 SCREW SET 10-32" X 1/4"
536 SCREW SET 10-32" X 3/16"
Q521 NUMBER CAP RH
Q555 NUMBER CAP LH
Q184 CLUTCH SPRING RH
Q183 CLUTCH SPRING LH
Q250 HANDLE WITH SET SCREW
Q605 DUST COVER RH
Q606 DUST COVER LH
151 HEX WRENCH 3/32"
Q194 TUBE BRUSH 3/8"
Q193 COLLET WRENCH 4 JAW
Q192 COLLET WRENCH 3 JAW
Q243 CLUTCH WELLS THREADED COMPLETE - FOR QUICK CHUCK ON WELLS R057 LATHE
Q246 CLUTCH BALDOR/RED WING COMPLETE - FOR QUCK CHUCK ON BALDOR OR RED WING
Q150 CLUTCH LINING WITH SCREWS - FOR ALL WELLS SUPER QUICK CHUCKS


SUPER QUICK CHUCK ACCESSORIES - FOR RIGHT HAND
Q203 ACCESSORY KIT RH
Q154 MANDREL WITH 1-64 SCREW RH
Q142 STONE CHUCK TOOTH AND KNIFE RH
Q188 STOPS (SET OF 6)
Q194 TUBE BRUSH
Q193 COLLET WRENCH 4 JAW
151 HEX WRENCH 3/32"
Q169 INSTALLATION SCREWS (PK OF 4)


SUPER QUICK CHUCK ACCESSORIES - FOR LEFT HAND   
Q200 ACCESSORY KIT LH
Q140 STONE CHUCK TOOTH AND KNIFE LH
Q152 MANDREL WITH 1-64 SCREW LH
Q124 ARBOR BAND CHUCK 3/4 LH
Q132 SPIRAL CHUCK LH
Q169 INSTALLATION SCREWS (PKG OF 4)
151 HEX WRENCH 3/32"
Q193 COLLECT WRENCH 4 JAW
Q194 TUBE BRUSH 3/8"
Q188 STOPS (SET OF 6)


SUPER QUICK CHUCK ADAPTERS
Q206 ADAPTER RED WING
- FITS ALL RED WING LATHES
Q212 ADAPTER BALDOR 210/211/221/240
- FITS BALDOR 210 AND 211 LATHES WITH 35mm OR 40mm BEARING.
- FITS BALDOR 221 AND 240 LATHES WITH 35mm OR 40mm BEARING.
- Q508 ADAPTOR RING 40mm IS INCLUDED FOR LATHES WITH 40mm BEARINGS.
NOTE: FITS LATHES WITH REMOVABLE CHUCK EJECTOR ASSEMBLY (see figure A)
Q218 ADAPTER BALDOR 300 SERIES
- FITS BALDOR 350, 353, 357, 359, 370, 380, AND 350T & 353T IF IT HAS THE END PLATE ILLUSTRATED IN FIGURE A WITH A REMOVABLE CHUCK EJECTOR ASSEMBLY.
Q223 ADAPTER ROBBINS AND MYERS
- FITS ROBBINS AND MYERS LATHE
Q226 ADAPTER RITTER A
- FITS RITTER MODEL A
Q229 ADAPTER RITTER C
- FITS RITTER MODEL C
Q237 ADAPTER BALDOR END PLATE
- FITS BALDOR 357T, 359T, 380T, WELLS R051, R052, R053, AND BALDOR 350T & 353T IF IT HAS THE END PLATE ILLUSTRATED IN FIGURE B WHERE THE CHUCK EJECTOR SCREWS DIRECTLY INTO THE END PLATE.
Q239 ADAPTER BALDOR 340 END PLATE
- FITS BALDOR 340 ONLY


DLS CORPORATION : (800)514-7063 / In California (714)282-9135

TOP OF PAGE - HOME - CONTACT US - REPAIR - LINKS - FAQ - MANUFACTURING
CATALOG - SPECIALS - PROMOS - NEW PRODUCTS - ECONOMY CORNER - USED EQUIPMENT - TEETH

Website by MrJ Design - Copyright 1998-2005 DLS Corporation